
RTD Process Calibrator - PIE 311
$2,094.00 – $2,209.00

RTD Process Calibrator - PIE 211
$1,460.00 – $1,575.00
pH and Voltage Process Calibrator – PIE 235
Calibrate your pH Instruments$1,073.00 – $1,158.00
Voltage Calibrator for all your process voltage signals
- Voltage calibrator sources three ranges of mV & V dc plus percent of 1 to 5 voltsWith the 235 you can check, calibrate and measure all your voltage, millivolt and pH signal instruments in your plant. Source -500.00 to 999.00 mV, 1.000 to 5.000 V, -25.00 to +125.00% of 1 to 5 V; 0.000 to 20.000 V.
- Power your loops with over 1,000 Ohm loadsThe 20.000 V range has an extended span of up to 24.000 Volts giving you a portable source for powering your loops.
- Read DC voltsThe 235 can measure from -500.00 to +999.00 mV, 0.000 to 5.100 V, -25.0 to 125.0 % of 1 to 5 V; 0 to 20.000 V and 0.00 to 60.00 V DC. Use it to check loop power supplies, I/V converters, 1 to 5 Volt signals, and other voltages.
- Save time calibrating recorders and monitors in 4 to 20 mA loopsOther brands of calibrators require that you break the loop to calibrate voltage inputs. With the PIE 235 you simply clip the test leads across the voltage inputs in a live 4 to 20 mA loop without disconnecting any wires.
- Simulate pH probes into transmitters & analyzersUse the pH simulator to verify proper operation of pH devices before you place a probe into a calibrated buffer.
- Quickly set any three outputs plus automatic stepping & rampingEasily set any value with the adjustable DIAL plus store any three output settings for instant recall with the EZ-CHECK switch. Choose between 2, 3, 5 & 11 steps to automatically increment output in 100%, 50%, 25% or 10% of span plus continuous ramp. Set step/ramp time to 5, 6, 7, 8, 9, 10, 15, 20, 25, 30 & 60 seconds.
- Use in the Plant, Field or ShopIncludes Rubber Boot and Attached Test Leads; Low profile switches resist accidental damage
- Simple Battery ChangesSeparate compartment for no-tool battery changes with four inexpensive “AA” batteries
See advantages of PIE 235 over Altek 235 →
Additional information
Weight | 2 lbs |
---|---|
Dimensions | 7.75 × 5.25 × 4.5 in |
Accessory Package |
Basic Package ,Standard Package |
Reviews (0)
Be the first to review “pH and Voltage Process Calibrator – PIE 235” Cancel reply
Datasheet, Manual and Calibration Procedures
Related products
New

Select options
This product has multiple variants. The options may be chosen on the product page
Wireless Diagnostic Calibrator – PIE 901
Milliamp, voltage and pressure calibrator $1,765.00 – $1,850.00
Select options
This product has multiple variants. The options may be chosen on the product page
Multifunction Diagnostic Calibrator – PIE 820Elite
Loop diagnostics $3,462.00 – $3,642.00
Select options
This product has multiple variants. The options may be chosen on the product page
Multifunction Diagnostic Process Calibrator – PIE 830
Two isolated channels $3,963.00 – $4,154.00Multifunction Diagnostic Panel Mount Calibrator – PIE 830PM
2 measurement channels $5,053.00
Select options
This product has multiple variants. The options may be chosen on the product page
Reviews
There are no reviews yet.